Read the forum code of contact
By: 26th July 2009 at 10:27 Permalink - Edited 1st January 1970 at 01:00
-Hello pics added??Included in the assembly there looks like a truck tyre valve.Is that a standard WW2 part??
By: 26th July 2009 at 11:11 Permalink - Edited 1st January 1970 at 01:00
-Hello pics added??Included in the assembly there looks like a truck tyre valve.Is that a standard WW2 part??
Yeh that schrader valve is a standard part, not sure of part number though. As for getting seals made hmm? Dont get em made in and fit em if the spit is going to come under the bowler hatted numpties in uk, if so you'll need to get the items sprinkled with holly water, blessed by the pope, and the original drawings sanctioned and authenticated, oh and original material. Apart from that, you'll be fine.
good luck.
Mick.
By: 26th July 2009 at 15:15 Permalink - Edited 1st January 1970 at 01:00
-Stunning drawing Ross. Is that Solidworks?
Good luck with your seals - hope someone can come up with an answer for you - might be difficult...
By: 26th July 2009 at 22:18 Permalink - Edited 1st January 1970 at 01:00
-Thanks
Stunning drawing Ross. Is that Solidworks?Good luck with your seals - hope someone can come up with an answer for you - might be difficult...
Hi,
We do use Solidworks but this assembly we have done up in ProDesktop which is a students version of ProEngineer.We have three guys doing the designs.One uses ProD exclusively,the other uses Solidworks exclusively and I mix between the two,rather unsuccesfully that is..We also use CAD as sometimes it is quicker and easier in some places.
With the rubbers we might try a brake reconditioning shop.
Cheers
By: 26th July 2009 at 22:38 Permalink - Edited 1st January 1970 at 01:00
-The seals are the same as for the flap selector, so yes, it is a standard part.
There is no source of original parts though - the conical seals will be easy enough to make - something like the Sealjet process will work.
The teeny tiny ones that are part of the valve are a different story. Makeable, but tricky!
Bruce
By: 26th July 2009 at 22:58 Permalink - Edited 1st January 1970 at 01:00
-Three programs eh? That's impressive. I'd like to start using a CAD program for the Whitley. Is there a straight forward but very good program you could recommend at all?
Hi,
We do use Solidworks but this assembly we have done up in ProDesktop which is a students version of ProEngineer.We have three guys doing the designs.One uses ProD exclusively,the other uses Solidworks exclusively and I mix between the two,rather unsuccesfully that is..We also use CAD as sometimes it is quicker and easier in some places.
With the rubbers we might try a brake reconditioning shop.
Cheers
By: 26th July 2009 at 23:57 Permalink - Edited 1st January 1970 at 01:00
-Thanks guys
The seals are the same as for the flap selector, so yes, it is a standard part.There is no source of original parts though - the conical seals will be easy enough to make - something like the Sealjet process will work.
The teeny tiny ones that are part of the valve are a different story. Makeable, but tricky!
Thanks Bruce..Will look into it.Still awstruck on the complexities of British assemblies..
Hi Whitley Project..
Try these out here and see what suits you best..
http://www.freebyte.com/cad/cad.htm
Basicly CAD is just like Tech Drawing of old but instead of rulers,squares and compasses all the lines are computer generated.Here is a screencap of CAD with one of our designs..All do different things better than others.
Posts: 2,605
By: QldSpitty - 25th July 2009 at 22:50 - Edited 2nd October 2019 at 11:40
Hi guys.
In the process of rebuilding our early brake relay for the Spit,the one that goes behind the rudder bar.We pulled it apart to draw it up and found it full of dirt and the rubbers perished.Otherwise in good condition.Is there somewhere we can get new rubbers ,diaphragms and what type of grease is used on the bearings?Will get some pics soon..
cheers Ross:cool: